bj4
Home News Industry News Get Pricing for A VFD Panel with Bypass Functionality
Technical Guide · Low Voltage Switchgear

Pricing a VFD panel with bypass comes down to the bypass type, the contactor rating and the transfer sequence. Here is how to read a quote line by line.

VFD Panel

Key takeaways

  • A bypass is a second path to the motor, not a spare drive.
  • The bypass contactor is sized on motor current, never on drive current.
  • Two contactors are cheaper than three, and they isolate less.
  • The transfer sequence is an interlock question before it is a wiring question.
  • A quote without a contactor rating and a transfer time cannot be compared.

Pricing a vfd panel with bypass looks simple until two quotes return at double the difference. Both say bypass. One isolates the drive, the other does not. This guide shows where the money and the risk sit in an industrial power panel of this type.

What the bypass actually switches

A bypass moves the motor feeder from the drive output to the incoming supply. The motor then runs on line voltage at fixed speed. The drive leaves the circuit.

That is the entire function. Nothing else in the cabinet changes, and nothing about the motor changes. The plant keeps pumping while the drive is repaired or replaced.

Most buyers assume the bypass is a backup drive. It is not. A drive controls frequency and torque. A bypass only keeps the shaft turning.

So the first question on any quote is not the drive model. It is what the bypass does to the drive terminals while the motor runs. A vfd drive panel that leaves its output live in bypass is an unsafe cabinet.

Three bypass arrangements and what each costs

Three arrangements dominate the market for vfd panels, and they differ in what they isolate. The price gap between them is wider than most buyers expect.

The cheapest is a two contactor set. One contactor feeds the drive, one connects the motor to the supply. The drive output stays connected to the motor terminals at all times.

The three contactor set adds an output contactor. Now the drive output can be opened before the bypass closes. That is the arrangement most plants should buy.

Small drives often carry an internal bypass. It is a switch inside the drive enclosure, rated for a fraction of the panel current. It suits a single small pump, not a plant.

ArrangementWhat it isolatesSwitchoverShare of panel costWhere it fits
No bypassNothing, the drive is the only pathNoneBaseProcess can stop with the drive
Two contactorThe drive input onlyManual or auto, 1 to 3 sRoughly one fifthSmall pumps, short outages
Three contactorInput and output, fully separatedManual or auto, 1 to 3 sA fifth to a thirdPumping stations, conveyors, fans
Internal bypassThe drive module, inside its own housingSwitch on the driveLeast, no extra cabinet widthDrives below about 30 kW

The width change is the hidden line. A three contactor bypass adds two devices and often one 600 mm section. That section carries its own busbar, its own door and its own share of the transport cost. Count it separately when you compare motor control panels between vendors.

The bypass contactor is sized on motor current

Three phase copper busbars on insulators inside a bypass panel, sized for motor full load currentPhase busbar
Load path

The current does not change when the path does

In bypass the motor draws its full load current through the bypass contactor, not through the drive. The busbar and the contactor see the same amps as a direct online starter.

That is why the rating on the drive nameplate is the wrong number to copy. Size the bypass group from the motor, then check the drive against the same figure.

A 75 kW motor at 400 V pulls roughly 135 A. The drive feeding it may be rated 150 A output. The bypass contactor has to break 135 A at locked rotor, in AC-3 duty, several times a shift.

Shops that copy the drive rating either overspend or undersize. Oversizing wastes money on a contactor nobody needed. Undersizing welds the contacts in the third year.

Electrical starters follow the same logic. A contactor is chosen by the load it switches. The cabinet it sits in does not decide the rating.

If you are unsure what is the purpose of a motor starter, the short answer is simple. It switches the motor and protects it from overload. In a bypass panel that job falls to the same device, on a different supply.

The busbar follows the contactor. A bypass section built for 250 A cannot take a 400 A motor later. Ask for the busbar rating in writing. The assembly should sit inside an IEC 61439 design verification, not outside it.

!
Do not copy the drive rating into the contactor line. The two numbers describe different jobs. A quote that lists one figure for both has not sized the bypass at all.

Where the money goes in a bypass line item

Terminal blocks and current transformer leads on a panel plate, the items a routine test record coversTerminal rows
The paper trail

The terminals are half of what you are buying

Every circuit in this row carries a number that appears on a drawing. In a bypass panel those numbers tell a fitter which way is the drive and which way is the supply.

A cabinet shipped without that mapping is a cabinet the plant rewires on a Sunday. That labour never appears on the quote, but it is paid all the same.

Ask for the quote broken into six lines and the differences stop hiding. Shell and busbar, drive, bypass group, control circuit, terminals and cable entry, test and documentation.

The bypass group is the line buyers under-read. It carries the contactors, the mechanical interlock, the extra busbar and the door space. On a three contactor panel it runs from a fifth to a third of the total.

The control circuit is the second blind spot. A bypass needs a control supply that survives when the drive is dead. That usually means its own transformer and its own set of fuses.

Documentation is the line most easily cut and the one that hurts later. A routine test record and a wiring diagram are part of the product, not a favour. Ask whether the works runs to an ISO 9001 quality system before you accept the price.

A metal electrical cabinet and a bypass panel look alike on a drawing. They are not the same purchase, and the line items prove it.

Interlocks decide the transfer sequence

Contactors and overload relays on three rails inside a VFD panel with a bypass, with door wiring and terminal rows on the right
Inside the bypass section

Three rails, and the order they switch in

1
Breakers first.Each outgoing way has its own protection, so a fault in bypass does not take the section down.
2
Contactors second.The drive and the bypass contactors sit side by side and share a mechanical interlock.
3
Overloads last.The thermal relay protects the motor on both paths, so it must sit downstream of the changeover.

The transfer is a sequence, not a switch. The drive output has to stop before the bypass closes. Reverse that order and the drive sees the supply on its output terminals.

Mechanical interlock stops two contactors closing together. Electrical interlock stops the sequence running in the wrong order. You need both, and the quote should say so.

An automation control panel adds a third layer. The PLC holds the sequence, checks the drive status and waits for the output to be confirmed dead.

That logic has to live somewhere. Good plc control panel design keeps the sequence in the PLC. It keeps the hard interlock in copper, so a failed program cannot backfeed the drive.

Manual bypass is cheaper and honest. Automatic bypass needs a status signal from the drive, a timer and a fail-safe check. Ask which one the price covers. The mcc bucket components change with the answer.

Cooling does not stop when the drive does

In bypass the drive is off, so it stops making heat. The contactors, the busbar and the choke keep working, and they keep warming the cabinet.

That surprises people. A bypass section is often hotter than the running drive section. The fan was wired to the drive and now sits idle.

Wire the panel fan to the incoming supply, ahead of the changeover. Then it runs in both modes and the cabinet stays inside its rating.

A small enclosure box bolted to a wall has the same problem with less room. A sealed box with 40 A of contactors inside needs a real thermal calculation, not a louvre.

Water plants and cement plants see this daily. A sump pump control panel that bypasses on every drive fault runs for weeks. It runs at line voltage, at ambient, with the door shut.

Size that cabinet for the bypass duty, not the drive duty. The IEA puts motors and their controls at roughly half of global electricity use. A cabinet that overheats in bypass is a cost the plant pays every hour.

?
Power the fan from the incoming side. Take it ahead of the changeover and it runs in both modes. Take it from the drive and the cabinet loses its cooling on the day it needs it most.

What a quotable specification has to state

A specification that can be priced states seven things. Every item maps to a line in the quote, and every missing item becomes an assumption.

  • The bypass type, written as no bypass, two contactor or three contactor.
  • The motor full load current, and the contactor AC-3 rating that follows it.
  • The interlock type, mechanical, electrical or both.
  • The transfer mode, manual or automatic, and the delay in seconds.
  • The cable entry, from the top or from the bottom, with gland plate size.
  • The control voltage, and whether the control supply survives the drive.
  • The test record, and whether the bypass was proven under load.

Your requisition may say panel vfd and the vendor will read the same cabinet. A control panel supplier quotes the seven items, not the file name. Put them in one email and the naming stops mattering.

Write the duty as well. Starts per hour, ambient temperature and the cable length to the motor change the contactor, the choke and the fan.

A quote that answers the seven items can be compared with another. A quote that answers three of them is a price for a different cabinet. The supplier should ask for the rest before quoting anyway.

Three questions that expose a thin quote

You do not need to be a panel builder to test a price. Three questions separate a real quote from a drawing that has not been done yet.

The first is what the bypass contactor is rated at, in amps, at AC-3. If the answer is the drive model number, the vendor has not sized it.

The second is what happens to the drive output when the bypass closes. If nobody can answer, the cabinet has a two contactor design pretending to be a three contactor one.

The third is whether the factory test covered a loaded transfer. A panel that has only been tested with the motor disconnected tells you nothing about contactor wear.

Vendors selling turn key solutions should welcome those questions. A price that survives them is worth the premium. A price that does not is a number looking for a signature.

A maintenance team gets value from proof. An industrial control panel builder who can show the transfer sequence is worth the premium. The saving is in the shift that does not stop.

Frequently asked questions

How much more does a bypass add to a VFD panel?
On a three contactor design the bypass group adds a fifth to a third of the panel cost. Cabinet width, busbar rating and interlock type move that figure. A two contactor set costs less and isolates less.
Can a bypass be added to an existing panel?
Often yes, if the enclosure has a spare section and the busbar can be extended. The work is a new door, a contactor group, an interlock and a revised drawing set. A sealed compact panel rarely has the room.
How long does a bypass transfer take?
One to three seconds is typical for a mechanical bypass with a controlled stop. The drive has to stop, the output has to be confirmed dead, then the bypass closes. Faster transfers need a different topology, not a faster contactor.
Does running in bypass damage the drive?
Not if the output is isolated first. Damage happens when the bypass closes with the drive output still live. That puts supply voltage on the drive terminals. That is the failure a three contactor design prevents.
Does bypass operation void the drive warranty?
Running the motor in bypass does not touch the drive, so it cannot void anything. Opening the drive or rewiring its output without isolation can. Keep the test record and the transfer sequence documented.
Do I need a bypass on a sump pump?
If the pump must run during a drive fault, yes. A sump pump control panel with a bypass keeps the pit dry during a repair. On a duty standby pair, the second pump covers that risk for less money.

Final thoughts

Three numbers price a vfd panel with bypass. They are the motor current, the contactor count and the transfer sequence. Get those three into the enquiry and the quotes arrive comparable. Leave them out and you will be comparing cabinet widths and hoping.

Send the motor schedule with the enquiry

Give us the motor list, the required bypass type and the site conditions. We will return a line by line quote with the contactor ratings and the test record attached.

Contact Giantele
GE

Giantele Engineering Team

Low voltage switchgear engineers at Zhejiang Zhegui Electric. We build IEC 61439 verified assemblies for factories, mines and utilities.

IEC 61439CEISO 9001

Get a Quote in 12 Hours

Send your project specs — our engineers reply with a verified price and IEC-compliant drawing within one working day.

MAKE AN ENQUIRY
or chat directly

+

Years

+

Countries

h

Reply
Build Your Switchgear Project with a Verified Chinese Manufacturer
Whether you are an EPC, a plant engineer, or a regional distributor — we deliver IEC-compliant low & medium voltage switchgear with full documentation, container-ready packing, and African-port logistics support.
12-hour response from our engineering team — not a sales bot.
NDA-friendly — share your single-line diagram without disclosing project name.
OEM/ODM welcome — your brand, our 13-year manufacturing backbone.
Free spec review — we flag IEC compliance gaps before you tender.
Request Engineering Consultation
MAKE AN ENQUIRY

Related Blogs

We will work with other excellent partners to deliver more high-quality products to the world.
MAKE AN ENQUIRY

Copyright © Zhejiang Zhegui Electric Co., Ltd. is founded in Zhejiang, China.   SItemap